Refrigerators are appliances that keep food fresh and cold. They are used in homes all over the world as a way to store food and beverages without spoiling them.
The refrigerator is an essential appliance in any household, but it can be difficult to work on when you’re not sure how to do so properly. To make matters worse, refrigerators often have complex systems that require specialized parts and tools, making the process even more daunting.
Thankfully, there are some basic tools for refrigerator repair that anyone can use to get started. Whether it’s a simple problem with your ice maker or a full-blown breakdown, these tools will help you get things done quickly and safely.
- 1/4″ drill bit (smaller size)
- 6mm tap
- Hand augur
- Needle nose pliers
- Plain screwdriver
Ice makers can break down unexpectedly, which means that if yours stops working, you need to fix it right away. The first step in repairing an ice maker is removing the plastic cover from the body of the appliance. With this removed, you can access the motor and remove the ice tray assembly.
A small 1/4″ drill bit is used to carefully pierce through the inside of the motor housing to release the ice tray. Using a 6mm tap, you can then loosen the screws holding the motor to the housing, allowing you to lift out the old motor and install the new one.
Once the motor is replaced, you can replace the ice tray itself using a hand augur. This tool is used to drive a metal rod into the ice tray holes to ensure they’re completely covered. Once the holes are filled, you can tighten the screws in place, replacing the ice tray with the plastic cover.
When you’ve finished fixing your ice maker, you can turn your attention to the condenser fan. Condensers are often responsible for cooling the refrigeration coils, which can lead to damage if they aren’t cleaned regularly.
To start cleaning your condenser, remove the three screws at the top of the unit. This will allow you to take off the front panel, exposing the condenser fans and coils. Remove the two screws in each condenser coil, then gently wipe both sides of the coil with a damp cloth to remove any dirt or debris.
If you find that the fans don’t spin freely, you may want to lubricate them by spraying them with WD40. However, this should only be used as a last resort.
After you’ve fixed your ice maker, you now know what tools you need to repair it. Keep reading below to learn about other useful tools for refrigerator repair.
A person can plan to get the fridge repair in the effective and efficient manner. The main motive of people is to reach the goals that will help in getting the favorable results. A person can choose the platform that provides quality of the services at a genuine rate to the people. A person can get the early repairs if they choose right professionals.
Water Filter System
- O-ring seal kit
- Rubber O-ring
- Drain hose
- Drill bits
You should always check your water filter system for leaks before attempting any repairs. In most cases, simply pulling the drain line will reveal whether or not there are any problems with the system.
If there isn’t a leak present, you’ll need to open up the filter tank to inspect the rubber o-rings. These are prone to wear out over time, causing the water flowing from the faucet to not be filtered properly. To inspect the o-rings, simply pull the drain hose free from the filter tank and slide it into the bottom of the tank. Now cut along the edge of the rubber ring to expose the inner portion of the ring.
Next, slide the cut section of the rubber ring into the hole in the bottom of the tank until it snaps into place. Repeat this process for all of the o-rings.
Once you’ve replaced the o-rings, you’ll need to reattach the drain hose to the filter tank. First, measure the length of the hose and mark where it needs to go. Then, using a rubber mallet and hammer, gently pound the hose into place. You can use the same process for attaching the end cap onto the filter tank to complete your repair.
Now that you understand how to fix common refrigerator issues, you’ll feel much more prepared to tackle the task of repairing larger issues like a broken compressor or freezer door. If you’re unsure about what issues you may face while fixing a refrigerator, consult an expert for advice!
- Allen wrench
- Small hammer
- 3M duct tape
- 8ft extension cord
- Wire snips
- Tape measure
Compressors are responsible for circulating air throughout the refrigerator. When they malfunction, they can cause serious damage to the entire appliance. Here’s how to diagnose and repair a bad compressor:
First, shut off the power to the refrigerator. Then, disconnect the wires coming from the compressor and label them accordingly. Next, attach the 8ft extension cord to both ends of the compressor using wire clips.
Using a tape measure, measure the distance between the fridge and its closest outlet. Make note of this measurement, as well as the length of the compressor, so you know how far to extend the cords. For safety purposes, also wrap electrical tape around the exposed wires to prevent accidental shocks.
With the wiring set up correctly, it’s time to connect the compressor to the power source. Attach the positive (+) side of the extension cord to the power plug, connecting the negative (-) side to the ground post. Plugging everything together ensures that no current flows back to the power supply. After completing the connection, you can test the compressor by switching it on and seeing if it runs smoothly.
Now that the compressor has been connected, it’s time to determine if the issue is with the compressor or the wiring. A good rule of thumb is to try and fix small problems first, since large ones are likely to be too complicated to repair. Start by checking for obvious signs of trouble such as overheating or smoke coming from the compressor.
If you notice anything suspicious, immediately stop using the refrigerator and contact a professional service for further assistance.
The last part of the process involves replacing the compressor. First, remove all of the wires from the fridge. Then, locate the bolts holding the compressor in place. Use an Allen wrench to loosen the bolt heads, followed by a hammer to remove the bolts from their respective posts. Finally, replace the compressor and tighten the bolts into place. Connect the wires once again and give the compressor a test run to confirm that it works normally.
Now that you’ve learned how to repair common refrigerator issues, you’re ready to tackle more challenging issues like the freezer door. Check out our list of the best replacement doors for the best results!//